Supermarkets: find the stores that cost more than they should.
With many stores, the waste hides in the average. VoltMap ranks every location against the others and tells you which store, which system and which hour.
- Grocery chains
- Convenience store groups
- Regional food retailers
Example case
Modeled exampleA regional grocer with 12 stores averaging $180,000 a year each. Three stores run well above the others per square foot, and nobody has had time to find out why.
- Annual electricity cost
- $2,160,000
- Locations
- 12
- Demand charges, share of bill
- 35%
- Service level
- Level 0–1
- Pricing model
- Savings share: 25% of direct utility savings, nothing upfront
| Annual Gross Value Delivered | $282,960 |
|---|---|
| Direct utility savings | $253,800 |
| Operational and AP value | $29,160 |
| Less: platform fee, 25% of direct utility savings$0 upfront. Operational and AP value is included free. | −$63,450 |
| Annual Net Value to Client | $219,510 |
| Year one | Each following year | |
|---|---|---|
| Annual Gross Value Delivered | $282,960 | $239,760 |
| Less: platform fee | −$63,450 | −$52,650 |
| Annual Net Value to Client | $219,510 | $187,110 |
The audit refund is counted once, in year one. The other items continue for as long as the service runs.
- Direct utility savings: counted in the savings share
- Operational and AP value: included free
Assumptions: Rate and tariff optimization: 8% of annual electricity cost; Historical bill audit refund, one-time: 2% of annual electricity cost, year one only; Peak and load optimization: 5% of demand charges; AP labor hours saved: 1.5 hours per location per month at $35 an hour; Late fees and usage spikes avoided: 1% of annual electricity cost
This is a modeled example, not a customer result. It uses the conservative default rates explained on the Annual savings page. Actual figures are confirmed on your own utility bills. How annual savings are calculated
What VoltMap does here
- Benchmarks every store per square foot and flags the outliers with the likely cause.
- Catches display cases and air conditioning left in day mode overnight.
- Staggers defrost cycles and start-ups so stores stop setting peaks they don't need.
How it is put in place
- Day 1
Connect
Authorize access to your utility accounts or upload 12 to 24 months of bills. Nothing is installed on site.
- Week 1
Baseline
VoltMap audits the bill history, builds a weather-adjusted baseline, and sends a savings opportunity report for your review.
- Weeks 2 to 4
First actions
The three highest-cost stores come first: night settings are corrected and defrost cycles staggered, then the same rules roll out to the rest.
- From day 30
Watch
Every new bill is collected and checked. Peak alerts arrive a day ahead, and equipment health alerts begin once 30 days of history are in place.
- Every month
Verify and settle
A statement compares each bill with the baseline. The platform fee is billed only on savings that have been verified.
How results are measured
- A baseline first
- Twelve to 24 months of your own history, adjusted for weather and operating hours, sets what the bill would have been.
- Verified on real bills
- Savings are confirmed on the utility bill itself: the rate applied, peak kW and kWh, line by line.
- Only bill savings are shared
- The platform fee applies to verified reductions and refunds on the utility bill. Hours saved and late fees avoided are reported but never billed.
- Reported every month
- One statement shows gross value, the fee and your net value. Enterprise customers can add an annual third-party audit.
Tracked for this sector: kWh per square foot by store, overnight base load, peak kW per store and the gap between best and worst locations.
See the numbers for your own sites.
Send three months of bills from up to three locations. We'll show what was overpaid and why, using your own figures.